+- FitnessForums (https://www.fitnessforums.net)
+-- Forum: Equipment (https://www.fitnessforums.net/Forum-Equipment)
+--- Forum: Looking For Parts (https://www.fitnessforums.net/Forum-Looking-For-Parts)
+--- Thread: Vision 9700hrt parts to sell (/Thread-Vision-9700hrt-parts-to-sell)
Vision 9700hrt parts to sell - Horseshowdad - 03-28-2014
I have a vision 9700hrt (approx. 2002-2004) that recently sped up to 12mph when my wife was using. I was able to get it to start again once but was unsuccessful subsequently. Dealer thought it was probably motor control board. Seeing how much those are I replaced treadmill.
So I now have the vision if anyone would like it for parts...it's been a rock solid treadmill and is built like tank. I assume both motors are good. They probably have 1000 miles on them both walking and running. The only obvious problem (other than being non-functional) is the console is worn and there's some corrosion from sweat (so that wouldn't be a good part).
I'm located in central Illinois. The machine weighs over 300lbs. Paid $2000 new. Willing to take $200 for parts.
Let me know if there's a market for this sort of parting out somewhere else of a very nice treadmill. Thanks.
I should have said that I'll provide pics if anyone wants to see them..let me know what.
RE: Vision 9700hrt parts to sell - razor sharp - 04-12-2014
I am looking for a part for my Vision Fitness T9700 HRT treadmill. Hopefully you can help. It is the center keypad membrane that controls the Start, Stop, Select, and both sets of Arrows. Could you shoot me a photo of the control faceplate so I can see if it matches mine?
RE: Vision 9700hrt parts to sell - Horseshowdad - 04-12-2014
(04-12-2014, 09:58 PM)razor sharp Wrote: I am looking for a part for my Vision Fitness T9700 HRT treadmill. Hopefully you can help. It is the center keypad membrane that controls the Start, Stop, Select, and both sets of Arrows. Could you shoot me a photo of the control faceplate so I can see if it matches mine?
hmmmm....that's the part the I'm having trouble with as well --so I don't think you want mine. I've been working on it for several days and I've been in touch with the manufacturer.
I thought they were going to give me some suggestions but they've basically said they don't recommend me trying to fix that switch and buy a new console.
Here's my symptoms -- I'm curious if they are close to yours. The treadmill will speed up to 12 mph for no reason...I can use the spped down button to get it to go down but it goes right back up. The funny thing is if I use the "user profile membrane switch" on the center membrane pins, everything works fine (although the buttons don't match up obviously). So that makes me suspect the center membrane. I've put a voltmeter on it and it looks ok to me except i'm wonder about the ground.
With the center membrane plugged in, it's a little unpredictable. Also, my console had some rust on it -- so I'm wondering if that screwed up the center membrane...is yours rusty by any chance. both motors are good and I think the boards are as well --
let's compare notes -- this is a 2002-2003 t9700hrt -- I'll send post a picture tomorrow of it. But bottom line, you don't want my center membrane switch as I'm repainting the ground on it (as a shot in the dark answer).
RE: Vision 9700hrt parts to sell - razor sharp - 04-13-2014
OK, here is my story.
I was doing some contract work for a retirement center and noticed the machine by their dumpster. They said they couldn't get it to work and were going to throw it away. They bought a new model.
They let me take this one.
I got home and it would only turn on. Nothing else worked. I called the manufacturer and was told to apply some heat gently to the console top.
I used a heat gun and messaged the control top with heat.
I was able to get the left and the right side keypad membranes to light up and "function", but not the center one. Of course, the center one controls the Start, Stop, Select, and Arrows. The main operating buttons!
After contacting the manufacturer again and finding out this part is "no longer available" I jumped onto the internet and made as many contacts as I found asking for this part. Made probably 50 calls. No luck.
Finally, last night I removed the right side membrane which controls the "program" buttons and plugged it into the center membrane prongs.
Everything (except of course the "programs") works fine, now.
I printed a paper lining up the new "functions" with their corresponding buttons and taped it in place.
It's not perfect, but our options were that or junk it.
If this is a procedure you ultimately choose to take I can guide you through it if you need help.
I will continue my efforts to locate a center keypad membrane, though not as diligent.
RE: Vision 9700hrt parts to sell - Horseshowdad - 04-13-2014
Our problems seem very similar - I understand what you are trying to do with the other membrane switch. I could do that as well but want to try to get the center membrane working or replaced -- I'm redrawing the ground circuit on it thinking maybe the rust compromised it (but I doubt it will work).
Let me know if you find the center membrane (where I can buy one too) or anything else you find -- I'll do the same.
I've attached a pic(s).
I can't get a picture to post/attach -- can someone tell me how to do that and I'll post pictures.
RE: Vision 9700hrt parts to sell - razor sharp - 04-14-2014
Will do, good luck
RE: Vision 9700hrt parts to sell - Horseshowdad - 04-16-2014
ok -- here something to check out Razor -- and anyone else -- try to take pin 3 (pin 1 is ground, pin 2 is neutral, pin 8-9 is elevation up & down) out of action -- bend it up and plug in the other 8....see if you get better results. I think I've isolated it down to pin 3 is causing unpredictable results (that's speed down and I'm hypothesizing that there's a short in that circuit). I have very predictable results without that in the mix and all buttons work.
You can also take the entire plug off and just use a jumper wire to actuate each circuit -- touch pin 2 and whatever pin you want for the function -- for example pin 2 and 5 will start the treadmill, 2 and 6 will stop it. pin 2 and 3 is speed up.
At the very least, we might be able to wire a single switch for speed down to bypass that circuit.
I know now that all the parts on this treadmill are good as it all works and is just a shorting problem if anyone is interested in the parts.
hope this helps.....
RE: Vision 9700hrt parts to sell - Horseshowdad - 04-17-2014
(04-16-2014, 10:27 PM)Horseshowdad Wrote: ok -- here something to check out Razor -- and anyone else -- try to take pin 3 (pin 1 is ground, pin 2 is neutral, pin 8-9 is elevation up & down) out of action -- bend it up and plug in the other 8....see if you get better results. I think I've isolated it down to pin 3 is causing unpredictable results (that's speed down and I'm hypothesizing that there's a short in that circuit). I have very predictable results without that in the mix and all buttons work.
You can also take the entire plug off and just use a jumper wire to actuate each circuit -- touch pin 2 and whatever pin you want for the function -- for example pin 2 and 5 will start the treadmill, 2 and 6 will stop it. pin 2 and 3 is speed up.
At the very least, we might be able to wire a single switch for speed down to bypass that circuit.
I know now that all the parts on this treadmill are good as it all works and is just a shorting problem if anyone is interested in the parts.
hope this helps.....
this looks like it worked -- I put a push button from radioshack on the speed down circuit and took the speed down membrane switch out of the loop....looks good -- further testing tomorrow.
RE: Vision 9700hrt parts to sell - razor sharp - 04-19-2014
Thanks for the update